Tanking is a waterproof membrane or liquid system installed beneath bathroom tiles. Its purpose is to stop water reaching vulnerable parts of the building, rather than relying on the decorative finish to keep everything dry. The protection needs to form a continuous layer across the areas exposed to water, including awkward edges that disappear once fittings are installed.
A tiled shower can look perfectly sound while moisture is getting through underneath. Understanding how tanking works helps you ask useful questions before a renovation begins. It also explains why careful preparation matters more than simply choosing attractive tiles. The background, waterproofing and tile finish need to work together, with particular attention to every connection and change of direction.
What a bathroom tanking cost allowance needs to include
A tanking kit price describes a purchase, not the cost of preparing and waterproofing a shower. The quotation should identify the protected wall and floor zones, corners, pipe openings and connections to the chosen tray or drain. Labour depends on the existing background and the detail of those junctions, not only the open surface area. Confirm that primers, compatible tapes or collars and the specified application stages are accounted for where the system requires them.
Ask whether damaged boards, moisture investigation and substrate repairs sit inside or outside the waterproofing allowance. Separate tiling and sanitaryware so tanking is neither omitted nor charged again elsewhere in the bathroom schedule. No tanking-only figure is established from this site's existing bathroom or wet room budgets. Request an itemised installed proposal and its VAT position, with the concealed-work checks and record agreed before tiling. A lower material-only price does not establish that the same protected construction will be delivered.
Why tiles and grout cannot do the whole job
Many tiles shed water readily, but a tiled surface contains joints, edges and openings. Grout can absorb moisture, and movement can create small cracks or gaps. Even where the tile itself has very low water absorption, that does not make the complete assembly waterproof. Water can still find a route through the surrounding details.
Tanking provides protection behind that visible surface. A liquid system forms a continuous coating when applied correctly, while a sheet membrane relies on properly formed joints and sealed connections. Neither approach compensates for loose boards or a leaking pipe. Waterproofing is part of a properly prepared construction, not a way to conceal existing defects.
Where the waterproof layer belongs
Shower enclosures need protection wherever regular spray reaches the walls. Around a bath, the extent depends on how it is used, especially whether there is a shower above it. Floors in wet zones may also need tanking, with the coverage planned around likely splashing and the chosen floor construction rather than an arbitrary border.
Corners and junctions deserve close attention because separate surfaces can move differently. Compatible tapes are commonly used where walls meet, where walls join floors and at board joints where required by the system. Pipe penetrations need suitable seals or collars. Connections to baths and shower trays must be detailed for the particular arrangement so water cannot bypass the membrane at its edge.
Choosing a sound background
The supporting surface must be stable, clean and suitable for both the waterproofing system and the weight of the tiling. Depending on the construction, this may involve appropriate tile backer boards or a prepared masonry background. Board selection, fixing centres and joint treatment need to follow the relevant instructions. A board being moisture resistant does not automatically make its joints waterproof.
Soft plasterboard, loose plaster and rotten timber should be investigated rather than covered. Floors need enough support to limit movement beneath a brittle tiled finish. Dust, contamination and unsuitable old coatings can prevent proper adhesion, so preparation may include removal, repairs or a compatible primer. Different materials have different requirements, and suitability should be checked before waterproofing begins.
When tanking happens during renovation
The usual sequence starts with stripping out and checking the exposed construction. First-fix services are positioned before the walls are closed, with electrical and plumbing tasks handled by qualified trades. Repairs and boarding follow, leaving a firm background with the necessary openings already formed. This reduces the need to disturb waterproofing to move a pipe later.
Tanking then goes on before tiling, once the background meets the required conditions. Liquid systems need the specified coverage, coats and drying intervals; sheet systems need correctly bonded overlaps or sealed joints. Corners, penetrations and tray connections should be checked while they remain visible. Adhesive and tiles follow only when the waterproof layer is ready, using compatible materials throughout the build-up.
Warning signs that deserve investigation
Loose tiles, staining on a ceiling below, soft boards and persistent mould can all indicate unwanted moisture. They do not prove that tanking was omitted. A supply leak, a failed waste connection, damaged sealant or poor ventilation may produce similar symptoms. The useful next step is to identify where the moisture originates, rather than assuming that fresh grout will solve it.
Look for patterns: does staining appear after showering, or does dampness remain when the bathroom has not been used? Avoid repeatedly soaking an area that is visibly deteriorating. If water is close to electrical fittings, stop using the affected area and seek appropriate professional help. Opening up a limited section may be necessary to establish the condition behind the tiles.
Checks before the tiles hide the details
Ask what system is proposed, which surfaces it will cover and how it connects to the tray or bath. Clarify how corners and pipe openings will be treated. These are practical questions about continuity, not a request for a particular brand. Photographs taken before tiling can provide a useful record, although pictures alone cannot establish that every application requirement was met.
After completion, care still matters. Keep ventilation working, inspect accessible sealant joints and deal with leaks promptly. Tanking protects concealed construction but does not remove the need for maintenance. If a fitting is later moved or a fixing passes through a protected area, the waterproof detail needs consideration again rather than assuming the original layer remains intact.
